PIP-5048MK inverter

non-EV Solar, Wind and other renewable power sources
non-EV batteries and other energy storage stuff
Forum rules
Important!
This forum is for discussion of Non-EV matters.
TitchRSA
Noobie
Posts: 5
Joined: Wed, 05 Jun 2019, 14:00
Real Name: Titch

Re: PIP-5048MK inverter

Post by TitchRSA » Wed, 12 Jun 2019, 17:13

@coulomb wrote:
Why is customer service so hard for so many Chinese (including Taiwanese) companies?
Yes indeed!

I have 12+ 4048MS out there. One system is 12kW and another 24kW. The freezing is a massive nuisance as it transfers the entire load to the batteries during the freeze - this is some 180A to 240A - not funny when you have 6 of these inverters on a single 3-phase estate.

Thank goodness I have a 600Ah battery bank on this system.

But that's not the point - is it? I have sent MPP charts, details, times, circumstances and well - they just haven't replied. These inverters will destroy my reputation

User avatar
coulomb
Site Admin
Posts: 3572
Joined: Thu, 22 Jan 2009, 20:32
Real Name: Mike Van Emmerik
Location: Brisbane
Contact:

Re: PIP-5048MK inverter

Post by coulomb » Wed, 12 Jun 2019, 21:18

suorama wrote:
Wed, 12 Jun 2019, 03:03
My inverters was with following specs:
U1 71 50
U2 01 12
U3 00 21
U4 00 00
You must have had PV off, or it was at night, for U4 to be 00.00.
After MCU update
U1 71 50
U2 02 00
U3 88 88
U4 01 10

After FW update
U1 71 80
U2 02 00
U3 00 21 (exept one left to 88 88)
That's back to what it was. It seems that 88.88 is the new display / Bluetooth firmware.
U4 01 10

So if you look that earlier post WatchPower screen shot, you can notice U1 is main CPU and U4 is secondary CPU.
My understanding is:
U1 is the firmware for the main DSP, as always
U2 is the firmware for some sort of co-processor or slave. That didn't seem to get changed with this pair of update files.
U3 is the firmware for the removable display with Bluetooth etc
U4 is the firmware for the Solar Charge Controller. WatchPower is still calling that the "secondary" firmware, from back when there were only two.
Learning how to patch and repair PIP-4048 inverter-chargers and Elcon chargers.

User avatar
coulomb
Site Admin
Posts: 3572
Joined: Thu, 22 Jan 2009, 20:32
Real Name: Mike Van Emmerik
Location: Brisbane
Contact:

Re: PIP-5048MK inverter

Post by coulomb » Wed, 12 Jun 2019, 21:39

suorama wrote:
Wed, 12 Jun 2019, 02:32
[edit] I remove links because of (and if I read right, there is at least two hardware versions. I do not know what version mine is. My inverters have label with 11/2018.
...
[/edit]
My guess is that your machine, from November 2018, is one of the oldest [ edit: actually, the first seem to be from August 2018], and this seems to be the very latest firmware (the latest we've heard of before this is 71.70). So I'd guess it would be safe to try.

I can probably dig out the URL from my browser history, if any users are desperate to try out this new firmware, and have a similarly aged machine. PM me with a photo of your machine's barcode sticker if interested.
Learning how to patch and repair PIP-4048 inverter-chargers and Elcon chargers.

suorama
Noobie
Posts: 18
Joined: Sun, 10 Mar 2019, 03:07
Real Name: Ari Sorvari
Location: Kangasala
Contact:

Re: PIP-5048MK inverter

Post by suorama » Wed, 12 Jun 2019, 23:04

Ok =)

Ofcourse I have also those files, so PM me also could work...
=)

User avatar
coulomb
Site Admin
Posts: 3572
Joined: Thu, 22 Jan 2009, 20:32
Real Name: Mike Van Emmerik
Location: Brisbane
Contact:

Re: PIP-5048MK inverter

Post by coulomb » Yesterday, 10:01

suorama wrote:
Wed, 12 Jun 2019, 02:32

After update, I can read all inverters through one.
@Suorama,
can you give a few details on how you updated?
  • Did you use the serial port or the USB port?
  • Did you have to press any buttons to get the inverter into update mode?
  • Was there anything else tricky?
Other users are getting comms errors attempting the update.
Learning how to patch and repair PIP-4048 inverter-chargers and Elcon chargers.

suorama
Noobie
Posts: 18
Joined: Sun, 10 Mar 2019, 03:07
Real Name: Ari Sorvari
Location: Kangasala
Contact:

Re: PIP-5048MK inverter

Post by suorama » Today, 05:38

No, there wasn't any tricky.

I must use serial. I do not have real serial port with my computer, so I use USB to serial adapter. That adapter is good one and works like real serial port.
That why I must use serial was, because that update program, what came with 7z pac, works only with serial.
When I update MCU I just start program "Remote Panel_Reflashtool.exe" in the computer and in the program I first select right serial port and then I push "Update MCU" to start update. Then that panel go to black and it took ~9min to erase and write per inverter (or maybe that was 6min).
When I update FW I just start program "AxpertKINGReflash.exe" in the computer and in program I first select right serial port and then I push "Update" button to start update. Then whole system "goes down" aka stop feeding my home and not charge or take any power from anywhere. Then panel shows to me:
UPDATE
YES?
I'm not sure if I must push the button next to YES word, so I push it.
Anyways, there wasn't any problems. That phase took also appr. 10 min per inverter.

I do all MCU updates first and then FW updates. (I have three inverters and 3phase system)

edit:
And ofcourse, first of all, I un(7)zip both packets to they own folders and start programs from those folders. With MCU I left all other setting as is (Baudrate 19200), only Serial was that what I choose.

[ Edit Coulomb: 7-Zip is a free program for zipping and unzipping archives; it is free to download. I have it installed, so I don't know if Windows knows what to do with a .7z file if it's not installed. Those needing more details, like which cables and USB to serial adapters to use, may find the PIP-5048MS firmware upload instructions helpful, but of course they won't apply perectly to the PIP-5048MK. ]

Post Reply